Easy Joint Paving Jointing Compound 12.5kg – Buff Sand

Product Information

I found that the shower or vertical setting on the hose nozzle works well with the installation of this product. When finishing the joints, a jointing tool may smooth out the surface of the joints to give a more pleasant look to the finish. The product should sit 1/8″ below the surface of the paver or bottom of the chamfer, whatever is lower. In my experience, it is an easy installation that takes about twice the time than a typical polymeric sand installation. I was certainly happy with the installation and the permeability of the product, especially for open graded bases. In tighter joints, it requires more patience to get the grains into the joints and may require a compactor to be able to achieve this or a thin tool to push it into the joints. A lot of water is required in the installation of this product and it is much easier with two or more people. A squeegee and / or soft bristle broom is required. Very fast to use: The use of water to wash and fill the joints between the paving is a breakthrough in jointing methodology. It assists the paving grout to compact into the joints so there is no need to 'strike' or 'tool' the joints unless you want a smooth finish. Driveway Jointing Mortar - High Strength Epoxy Resin Paving Grout - suitable for vehicle areas up 3.5 tonnes Easyjoint can be used in wet or dry conditions and is sold in a 12.5kg tub which will cover an average of 7m² depending on slab size and joint width.

Polymeric sand cannot be installed in the rain. This is where this product shines. Early or late in the season, we see a lot of rain and colder temperatures making it extremely difficult to wrap up projects and get paid. However, this can be installed in these conditions allowing you to wrap projects up for your clients and get paid.

Contact Us

Technically advanced: Years of research and continuous development of our jointing compound makes this a market leader. We sell tens of thousands of EASYJoint tubs every month throughout the UK and in Europe. The original jointing compound for all weather paving. It can be used rain or shine, at any time with an oustanding finish. Available in different colours, EasyJoint holds up well against weathering and is incredibly long-lasting on joints that are 3mm wide and over. Once opened, the remaining product can still be used, in turn reducing waste and making the most of your money. The result of using EASYJoint, to joint your paving, will be a paving gap that is completely filled without the need for kneeling and compressing the material by hand that will last for years. A strong joint that will resist the elements and stand the test of time - better than traditional jointing methods. Compact the pavers or slabs using a compactor with a protective pad to set them into the bedding layer prior to beginning the installation of the jointing compound.

Similar to the above systems, paver base panels have drainage holes in them and when installed with High Performance Bedding below, this system allows water to flow through it and into the subgrade following a slope out of the system. • Early or Late in the Season That being said, there is no haze issue that you may get with polymeric sand and it is a much easier product to install in terms of the potential for failure. It is most definitely the perfect product for the applications listed above and in some cases can be superior to polymeric sand as long as the base is free-draining. Smooth the joints: when drained and dried, lightly "point" or "strike" the joints with a suitable finishing tool No Waste: Opened tubs of EASYJoint, if not fully used, can be kept for later use providing they are covered by a minimum of 2" (50mm) or more of water. – There is no waste with our jointing compound, EASYJoint is an environmentally friendly product.

Azpects EASYJoint

To further aid this, "point" or "strike" the joint; do not leave it textured. This ensures the top of the filler is below the top rounded edge of the paving and helps it adhere to the base and sides of the paving material. Pre-wet the pavers or slabs and begin to work in small 100 square foot areas to install the jointing compound and pre-wetting the next 100 square foot area when you move onto it. You do not want to install this jointing compound onto a dry surface. Wet the paving, brush in the compound, then strike the joints for a smooth finish and stronger, durable joint.